Accruepole Private Limited

As per IS -15908: 2011 Standard. ?16 X 2 Dot Matrix LCD Display. ?Standby battery backup with built in charging. ?Fire / Fault status in unambiguous colored LED indication. ?Switch Mode Power Supply. ?Tactile Keypad for easy panel operation. ?System ON indication. ?Main, Standby status indication. ?Low Battery visual warning with audible tone. ?Relay output for actuators, for Fire and Fault. ?Lamp Test facility. ?Zone wise one man Walk Test Facility. ?Zone wise Isolation facility with loop voltage cut off. ?Compatible to all type of Conventional Detectors. Optional Zone Wise Sounder / Zone Wise Contact

RE-25SS sounder cum strobe are designed to simplify installations to provide primary and secondary for fire and security applications. These are ideal where smaller notifications devices is desired. The horns can be flush / ceiling mounted with / without back box. Strobe shall be wired as primary (or) secondary signaling notification appliance flashing at 1Hz over entire voltage operating range. Strobe light consists of Xenon flash tube. 

FIRE ALARM CONTROL PANEL 

ravel fire alarm system ,
Microprocessor based conventional Fire Alarm Control Panel
This can be used as a standalone or networkable panel.

An automatic fire alarm system–typically made up of smoke detectors, heat detectors, manual Call Points, audible warning devices, and a fire alarm control with remote notification capability–can provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire. The Manufacturer recommends that smoke and/or heat detectors be located throughout a protected premise following the recommendations of the current edition of the National Fire Protection Association Standard 72 (NFPA 72), manufacturer's recommendations, State and local codes, and the recommendations contained in the Guide for Proper Use of

Switched Mode Power Supply.
Modular Construction ?Auto Resettable Fuse
Surge Protection for all Input and outputs.
Programmable AC loss delay/Trouble Remainder/Alarm Verification
Battery polarity reversible protection
Surface Mount Technolog

An automatic fire alarm system–typically made up of smoke detectors, heat detectors, manual Call Points, audible warning devices, and a fire alarm control with remote notification capability–can provide early warning of a developing fire. Such a system, however, does not assure protection against property damage or loss of life resulting from a fire. The Manufacturer recommends that smoke and/or heat detectors be located throughout a protected premise following the recommendations of the current edition of the National Fire Protection Association Standard 72 (NFPA 72), manufacturer's recommendations, State and local codes, and the recommendations contained in the Guide for Proper Use of System Smoke Detectors, which is made available at no charge to all installing dealers. A study by the Federal Emergency Management Agency (an agency of the United States government) indicated that smoke detectors may not go off in as many as 35% of all fires. While fire alarm systems are designed to provide early warning against fire, they do not guarantee warning or protection against fire. A fire alarm system may not provide timely or adequate warning, or simply may not  

Ravel Manual Call Point RE- 716MR
Fire Alarm Conventional Manual call Point

Operates on 24 VDC. ! Green Colored for Gas Release. ! Yellow Colored for Gas Abort. ! 1 No’s of CO & NC Output. A

ot Matrix LCD display.
Alphanumeric keypads.
RS 485 Communication for Network Repeater. System ON, AC ON, Battery ON, Charger ON indications.
Lamp test facility. Maximum 16 panels including repeater can be connected in a Single Network via RS-485.
Repeater Panel can monitor the status of RE-900 series panels via RS-485 Network communication.
User can Disable / Enable the Zone of Fire Alarm Control Panel Connected in network.

Dual LED’s for 360 visibility. Ÿ Advanced detection and communication protocol. Ÿ Easy installation and maintenance. Ÿ Sleek low -profile housing design. Ÿ Regular 100mm Base. Ÿ EN-54 Standard. Operating Voltage : 10 ~ 28V DC. O O Operating Temperature : 0 C to 37.8 C. Relative Humidity : 10% to 90% Reset Voltage : less than 1V. Stand by Current : 85 Micro Amps. Start Up Time : 30 Seconds. Cycle time : 28 - 35 Seconds. Alarm Current : 60 mA (Max.). Remote Output : 15mA maximum open collector. Smoke Sensitivity : 0.10 to 0.16 dB/m. O O Thermal Rating : 57 C(135 F). Alarm Contact Rating C,NO : 1A @ 30 VDC; 0.5A @ 125VAC. C,NC : 1A @ 30 VDC; 0.5A @ 125VAC (Optional On Order Basis)

As per IS -15908: 2011 Standard. 16 X 2 Dot Matrix LCD Display. Standby battery backup with built in charging. Fire / Fault status in unambiguous colored LED indication.Switch Mode Power Supply.Tactile Keypad for easy panel operation.System ON indication.Main, Standby status indication.Low Battery visual warning with audible tone. Relay output for actuators, for Fire and Fault.Lamp Test facility Zone wise one man Walk Test Facility. Zone wise Isolation facility with loop voltage cut off.Compatible to all type of Conventional Detectors. Optional Zone Wise Sounder / Zone Wise Contact.

RE-120GR is a microprocessor based Agent Release Panel. These panel are a feature packed control unit performing dual function of detection and controlled release of gaseous agent. These panels have 2 detection circuits and 1 agent release circuit with various programmable options. The panel have all the safety features to prevent accidental release, easy to install, commission with user friendly programmable option, this panel is ideal choice to protect the premises

Ravel Fire Alarm Hooter RE- 24CS
Fire Alarm system
Fire Alarm Conventional Hooter
Sounders are designed to simplify installations to provide primary and secondary for fire and security applications

Ravel Indian Manufacturer, International standard. ? Modular Construction, Serviceable. ? Special logic circuitory to prevent accident release. ?Auto Resettable Fuse. ? Surge Protected. ? Battery polarity & deep discharge protection. ?Variable solenoid ON / OFF time. 2 No’s of programmable Initiating Device Circuit and 1 No. of Releasing Agent circuit.

* Complies with UL -864 and NFPA-72. * * Operates on 120 - 220v 60 /50 Hz, AC Mains power supply. * Standby (battery) backup 24v DC power supply with builtin charger. * Touch Keypad for user friendly operation. * Epoxy powder coated finish. * Class- B, Style B / C initiating device circuit (IDC). * All zones accept smoke detectors and any normally open contact device. * Class B Notification Appliance Circuits (NAC). * NAC shall be programmed as auto silence / Silence Inhibit. * Error free Fire / Fault status in unambiguous colored LED indication. * 1000 Event storage with RTC. * Main, Standby status with audible and visual indication. * Two Form C relays for fire and fault. * Resettable / Steady 24V D.C. Output. * RS 485 Communication facility. * TCP/IP facility (Optional) *MODBUS for BMS integration (Optional). * PC software (optional) * External Zone Wise Sounder/Contact via RS 485 (Optional). * All field wiring circuits are supervised. * Zone Isolation facility with loop voltage cut off. * Zones available : 12, 16, 20, 24, 32, 48, 64,96 and 128. * Facility to connect Public Address System (PA) through RS-485 Communication.

Fully complies with UL -864 and NFPA-72. 
Rugged CRCA sheet with powder coated finish. Operates on 110 - 220v 50 /60 Hz, AC Mains power supply.
16x2 Dot Matrix LCD Display. 4/8 Class B Style ‘B ‘ or Style ’C’ 
initiating device circuit (IDC). 
All zones accept smoke detectors and any normally open contact device.
Any Zone can be configured as Alarm or supervisory Zone.
2 Class B Notification Appliance Circuits (NAC).  NAC shall be programmed as silenceable or Non Silenceable. 
Supervisory Zone shall be Latching or Resettable. 
Standby (battery) backup 24v DC power supply with built in charger 
Error free Fire / Fault status in unambiguous colored LED indication.
System ON indication.
Main, Standby status audible and visual indication.
Battery Low visual warning with audible tone. ? FormC relays for fire, fault and supervisory.
Resettable / Steady 24V D.C. Output. ? RS 485 Communication facility (Optional). 
Lamp Test facility. ? All field wiring circuits are Power limited except 110 - 220v AC and Battery.
All field wiring circuits are supervised. 
Walk Test facility.
Zone Isolation facility with loop voltage cut off. Earth fault annunciation facility at 0 ohms.
AC Low voltage cutoff.
Programmable AC loss delay. 
Programmable Alarm verification.